Tnmotown Dyno Results, PICS/VIDS INSIDE

**MAXX** · 03-17-2010

Well Tino and I took a trip to see Rick today at Synergy Motorsports. Tino has not yet had his car tuned for the nos setup. Good thing we went today, LOL!!! Rick also suggest that Tino think about doing a speed density tune, Tino agrees and goes forward with it.

On the 1st two pulls Rick was like "What the fuck?" Tino what have you done to your car since last time here? Tino told him he took off his last exhaust and put a Flowmaster RACE 1 chamber system on, different spark plugs, and these new injectors I just installed in your parking lot. Tino made 20rwhp less hp then last time in. Rick suggest he cut off the flowmaster. Tino cuts it off. Rick redynos the car.....WTF The car made 30rwhp more without the 1 chamber. No more 1 chambers from here on out Tino said, LOL!!!

On the 1st Nos pull Rick notices that Tino is not getting the NOS feed to make the car kick hard, just doesn't seem like the nos is kicking in he says. And the numbers are showing. Solenoids are kicking on, WTF??? Come to find out Tino had left the shradder valve in the fuel rail, causing the fuel not to mix with the nitrous. Fixed that problem. So with the car running better and a little rich on top due to possible a higher fuel jet on the plate kit Tino's car runs harder now then people have seen it on the streets and is running correct now Thanks to Rick and his help going over the problems.

Now numbers, pics, and videos.

2001 Camaro LS1
Cam/LT's/NOS Plate Kit/4.10's/M6/Speed Density Tuned

391rwhp/375rwtq with the 1 chamber flowmaster On
.
421rwhp/390rwtq without the 1 chamber flowmaster
.
530rwhp/600rwtq with the Nos Plate kit

Some Pics of the day

Video #1 with the Flowmaster 1 Chamber on 391rwhp/375rwtq
YouTube - Maxxlimit "Tnmotown" Flowmaster 1 Chamber Dyno Pull

Video #2 without the Flowmaster 1 Chamber on 421rwhp/390rwtq
YouTube - Maxxlimit "Tnmotown" Non-Flowmaster Dyno Pull

Video #3 with the Nos Plate Kit 530rwhp/600rwtq
YouTube - Maxxlimit "Tnmotown" Nos Dyno Pull

Tino and I would like to again thanks Rick at Synergy Motorsports for getting Tino in on short notice and help with the few problems Tino had.

And for your guys info, I have proof on video that Flowmaster sucks dick, even there RACE 1 CHAMBER MUFFLER!!!!! Might sound good, but performs like garbage.

**67sbc** · 03-17-2010

Man thats a sweet car.. Puts down some power too!! I ran flowmasters then switched over to coffin mufflers. I noticed a night and day differece in power. You should check them out

**Nate @ All Out Performance** · 03-17-2010

Im a dynomax fan,flows are garbage.

**tnmotown** · 03-17-2010

Thanks guys, yeah I heard good stuff with dynomax. Never ever EVER will I touch flowmasters again.

Anyways, yeah it made some good power. Just a few tweaks to still work on, would like to get that 550rwhp mark. Nonetheless, very happy!

**beezer1519** · 03-18-2010

good stuff tino, i already grinded down the calipers wheels are ready to go on once i break in my new clutch... when are you going to take it to the track?

**tnmotown** · 03-18-2010

Originally Posted by beezer1519

good stuff tino, i already grinded down the calipers wheels are ready to go on once i break in my new clutch... when are you going to take it to the track?

Im waiting to get a new clutch also! lol, this stocker isnt holding up. That and some good tires, a day off work, then I should be good to go